Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

Author: trini

arch/powerpc/cpu/mpc85xx/cmd_errata.c

@@ -299,6 +299,9 @@ static int do_errata(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 #ifdef CONFIG_SYS_FSL_ERRATUM_A007212
 	check_erratum_a007212();
 #endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
+	puts("Work-around for Erratum A-005434 enabled\n");
+#endif
 
 	return 0;
 }

arch/powerpc/cpu/mpc8xxx/cpu.c

@@ -67,6 +67,7 @@ static struct cpu_type cpu_type_list[] = {
 	CPU_TYPE_ENTRY(G4860, G4860, 0),
 	CPU_TYPE_ENTRY(G4060, G4060, 0),
 	CPU_TYPE_ENTRY(B4440, B4440, 0),
+	CPU_TYPE_ENTRY(B4460, B4460, 0),
 	CPU_TYPE_ENTRY(G4440, G4440, 0),
 	CPU_TYPE_ENTRY(B4420, B4420, 0),
 	CPU_TYPE_ENTRY(B4220, B4220, 0),

arch/powerpc/include/asm/config_mpc85xx.h

@@ -247,7 +247,9 @@
 #define CONFIG_SYS_FSL_ERRATUM_ELBC_A001
 #define CONFIG_SYS_FSL_ERRATUM_ESDHC111
 #define CONFIG_SYS_FSL_ERRATUM_A005125
+#ifndef CONFIG_USB_MAX_CONTROLLER_COUNT
 #define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+#endif
 
 #elif defined(CONFIG_P1021)
 #define CONFIG_MAX_CPUS			2
@@ -591,6 +593,7 @@
 #define CONFIG_SYS_FSL_ESDHC_P1010_BROKEN_SDCLK
 #define CONFIG_SYS_FSL_PCIE_COMPAT	"fsl,qoriq-pcie-v2.2"
 #define CONFIG_SYS_FSL_ERRATUM_A005125
+#define CONFIG_SYS_FSL_ERRATUM_A005434
 #define CONFIG_SYS_FSL_ERRATUM_I2C_A004447
 #define CONFIG_SYS_FSL_A004447_SVR_REV	0x11
 #define CONFIG_ESDHC_HC_BLK_ADDR

arch/powerpc/include/asm/processor.h

@@ -1117,6 +1117,7 @@
 #define SVR_C293	0x850030
 #define SVR_B4860	0X868000
 #define SVR_G4860	0x868001
+#define SVR_B4460	0x868003
 #define SVR_G4060	0x868003
 #define SVR_B4440	0x868100
 #define SVR_G4440	0x868101

board/freescale/common/sys_eeprom.c

@@ -21,7 +21,7 @@
 /* some boards with non-256-bytes EEPROM have special define */
 /* for MAX_NUM_PORTS in board-specific file */
 #ifndef MAX_NUM_PORTS
-#define MAX_NUM_PORTS	23
+#define MAX_NUM_PORTS	16
 #endif
 #define NXID_VERSION	1
 #endif
@@ -58,8 +58,9 @@ static struct __attribute__ ((__packed__)) eeprom {
 	u8 res_1[21];     /* 0x2b - 0x3f Reserved */
 	u8 mac_count;     /* 0x40        Number of MAC addresses */
 	u8 mac_flag;      /* 0x41        MAC table flags */
-	u8 mac[MAX_NUM_PORTS][6];     /* 0x42 - x MAC addresses */
-	u32 crc;          /* x+1         CRC32 checksum */
+	u8 mac[MAX_NUM_PORTS][6];     /* 0x42 - 0xa1 MAC addresses */
+	u8 res_2[90];     /* 0xa2 - 0xfb Reserved */	
+	u32 crc;          /* 0xfc - 0xff CRC32 checksum */
 #endif
 } e;
 

board/freescale/p1_p2_rdb/Makefile

@@ -4,8 +4,27 @@
 # SPDX-License-Identifier:	GPL-2.0+
 #
 
+MINIMAL=
+
+ifdef CONFIG_SPL_BUILD
+ifdef CONFIG_SPL_INIT_MINIMAL
+MINIMAL=y
+endif
+endif
+
+ifdef MINIMAL
+
+obj-y	+= spl_minimal.o tlb.o law.o
+
+else
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
 obj-y	+= p1_p2_rdb.o
+obj-$(CONFIG_PCI)  += pci.o
+endif
 obj-y	+= ddr.o
 obj-y	+= law.o
-obj-$(CONFIG_PCI)  += pci.o
 obj-y	+= tlb.o
+
+endif

board/freescale/p1_p2_rdb/ddr.c

@@ -180,27 +180,22 @@ fsl_ddr_cfg_regs_t ddr_cfg_regs_800 = {
 
 phys_size_t fixed_sdram (void)
 {
-	char buf[32];
 	fsl_ddr_cfg_regs_t ddr_cfg_regs;
 	size_t ddr_size;
 	struct cpu_type *cpu;
 	ulong ddr_freq, ddr_freq_mhz;
 
 	cpu = gd->arch.cpu;
-	/* P1020 and it's derivatives support max 32bit DDR width */
-	if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {
-		ddr_size = (CONFIG_SYS_SDRAM_SIZE * 1024 * 1024 / 2);
-	} else {
-		ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
-	}
+
+	ddr_size = CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
+
 #if defined(CONFIG_SYS_RAMBOOT)
 	return ddr_size;
 #endif
 	ddr_freq = get_ddr_freq(0);
 	ddr_freq_mhz = ddr_freq / 1000000;
 
-	printf("Configuring DDR for %s MT/s data rate\n",
-				strmhz(buf, ddr_freq));
+	printf("Configuring DDR for %ld T/s data rate\n", ddr_freq);
 
 	if(ddr_freq_mhz <= 400)
 		memcpy(&ddr_cfg_regs, &ddr_cfg_regs_400, sizeof(ddr_cfg_regs));
@@ -211,8 +206,7 @@ phys_size_t fixed_sdram (void)
 	else if(ddr_freq_mhz <= 800)
 		memcpy(&ddr_cfg_regs, &ddr_cfg_regs_800, sizeof(ddr_cfg_regs));
 	else
-		panic("Unsupported DDR data rate %s MT/s data rate\n",
-					strmhz(buf, ddr_freq));
+		panic("Unsupported DDR data rate %ld T/s\n", ddr_freq);
 
 	/* P1020 and it's derivatives support max 32bit DDR width */
 	if (cpu->soc_ver == SVR_P1020 || cpu->soc_ver == SVR_P1011) {

board/freescale/p1_p2_rdb/spl.c

@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <malloc.h>
+#include <mmc.h>
+#include <nand.h>
+#include <i2c.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SYSCLK_MASK	0x00200000
+#define BOARDREV_MASK	0x10100000
+
+#define SYSCLK_66	66666666
+#define SYSCLK_100	100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 val_gpdat, sysclk_gpio;
+
+	val_gpdat = in_be32(&pgpio->gpdat);
+	sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+	if (sysclk_gpio == 0)
+		return SYSCLK_66;
+	else
+		return SYSCLK_100;
+
+	return 0;
+}
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L2_SIZE;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, bus_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	console_init_f();
+
+	/* Set pmuxcr to allow both i2c1 and i2c2 */
+	setbits_be32(&gur->pmuxcr, in_be32(&gur->pmuxcr) | 0x1000);
+	setbits_be32(&gur->pmuxcr,
+		     in_be32(&gur->pmuxcr) | MPC85xx_PMUXCR_SD_DATA);
+
+	/* Read back the register to synchronize the write. */
+	in_be32(&gur->pmuxcr);
+
+#ifdef CONFIG_SPL_SPI_BOOT
+	clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_SD_DATA);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+	gd->bus_clk = bus_clk;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     bus_clk / 16 / CONFIG_BAUDRATE);
+#ifdef CONFIG_SPL_MMC_BOOT
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI Flash boot...\n");
+#endif
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	/* Pointer is writable since we allocated a register for it */
+	gd = (gd_t *)CONFIG_SPL_GD_ADDR;
+	bd_t *bd;
+
+	memset(gd, 0, sizeof(gd_t));
+	bd = (bd_t *)(CONFIG_SPL_GD_ADDR + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L2_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L2_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+#endif
+	/* relocate environment function pointers etc. */
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	gd->ram_size = initdram(0);
+#ifdef CONFIG_SPL_NAND_BOOT
+	puts("Tertiary program loader running in sram...");
+#else
+	puts("Second program loader running in sram...\n");
+#endif
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}

board/freescale/p1_p2_rdb/spl_minimal.c

@@ -0,0 +1,84 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <ns16550.h>
+#include <asm/io.h>
+#include <nand.h>
+#include <linux/compiler.h>
+#include <asm/fsl_law.h>
+#include <fsl_ddr_sdram.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+#define SYSCLK_MASK	0x00200000
+#define BOARDREV_MASK	0x10100000
+
+#define SYSCLK_66	66666666
+#define SYSCLK_100	100000000
+
+unsigned long get_board_sys_clk(ulong dummy)
+{
+	ccsr_gpio_t *pgpio = (void *)(CONFIG_SYS_MPC85xx_GPIO_ADDR);
+	u32 val_gpdat, sysclk_gpio;
+
+	val_gpdat = in_be32(&pgpio->gpdat);
+	sysclk_gpio = val_gpdat & SYSCLK_MASK;
+
+	if (sysclk_gpio == 0)
+		return SYSCLK_66;
+	else
+		return SYSCLK_100;
+
+	return 0;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_SYS_NAND_BR_PRELIM) && defined(CONFIG_SYS_NAND_OR_PRELIM)
+	set_lbc_br(0, CONFIG_SYS_NAND_BR_PRELIM);
+	set_lbc_or(0, CONFIG_SYS_NAND_OR_PRELIM);
+#endif
+
+	/* initialize selected port with appropriate baud rate */
+	plat_ratio = in_be32(&gur->porpllsr) & MPC85xx_PORPLLSR_PLAT_RATIO;
+	plat_ratio >>= 1;
+	gd->bus_clk = CONFIG_SYS_CLK_FREQ * plat_ratio;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     gd->bus_clk / 16 / CONFIG_BAUDRATE);
+
+	puts("\nNAND boot... ");
+
+	/* copy code to RAM and jump to it - this should not return */
+	/* NOTE - code has to be copied out of NAND buffer before
+	 * other blocks can be read.
+	 */
+	relocate_code(CONFIG_SPL_RELOC_STACK, 0, CONFIG_SPL_RELOC_TEXT_BASE);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	puts("\nSecond program loader running in sram...");
+	nand_boot();
+}
+
+void putc(char c)
+{
+	if (c == '\n')
+		NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, '\r');
+
+	NS16550_putc((NS16550_t)CONFIG_SYS_NS16550_COM1, c);
+}
+
+void puts(const char *str)
+{
+	while (*str)
+		putc(*str++);
+}