Issues

• Project status

  synthetos/g2#516 · Filter by author timonsku opened on Jan 3, 2024
  5

• Is G2core a good choice for my app?

  synthetos/g2#515 · Filter by author rayz55 opened on May 5, 2023

• Spindle Enable Pin Not Functioning

  synthetos/g2#510 · Filter by author mertzk opened on Apr 19, 2022
  1

• UART on g2core

  synthetos/g2#508 · Filter by author XavierCuenca opened on Apr 5, 2022

• feedrate interpretation for moves involving both, primary axes (XYZ) and secondary linear axes (UVW) differs from LinuxCNC

  synthetos/g2#503 · Filter by author DerAndere1 opened on Dec 21, 2021

• Soft Limits not setting alarm state. Not stopping job.

  synthetos/g2#500 · Filter by author discoordination opened on Jul 22, 2021
  1

• Not emitting steps at shallow incline.

  synthetos/g2#493 · Filter by author lutorm opened on Apr 14, 2021
  7

• Edge: axis names in text mode position reports (contains patch)

  synthetos/g2#489 · Filter by author prof7bit opened on Jan 28, 2021
  1

• Edge: U,Y,W axes don't work in probe commands (G38.x)

  synthetos/g2#488 · Filter by author prof7bit opened on Jan 28, 2021
  1

• edge-preview: missing acceleration/deceleration when sending multiple moves at once

  synthetos/g2#487 · Filter by author prof7bit opened on Jan 7, 2021
  1

• Wrong enum used for axis configuration

  synthetos/g2#486 · Filter by author benlaurie opened on Jan 1, 2021
  1

  

• Homing on U,V or W axis is not possible

  bugin progress
  synthetos/g2#482 · Filter by author prof7bit opened on Oct 21, 2020
  36

  

• UVW Axis limit switches, documentation missing, configuration missing

  synthetos/g2#481 · Filter by author prof7bit opened on Oct 20, 2020
  7

• New “kill” behavior seems inconsistent with State Model for Feedhold and Job Kill (and bad location on hold)

  bugin progress
  synthetos/g2#480 · Filter by author tedh-shopbot opened on Oct 15, 2020
  

• Status Report requested just before move starts sometimes reports target location rather than current location

  bugin progress
  synthetos/g2#479 · Filter by author tedh-shopbot opened on Oct 7, 2020
  3

  

• G4 not dwelling with non-movement commands

  bugin progress
  synthetos/g2#478 · Filter by author wholetthedogsout opened on Oct 7, 2020
  5

  

• Better jogging support

  enhancement
  synthetos/g2#473 · Filter by author lllars opened on Jun 30, 2020

• incorrect input pin state after glitch

  synthetos/g2#470 · Filter by author lllars opened on Jun 18, 2020
  23

• Configure Spindle PWM Control on ArduinoDue gShield

  synthetos/g2#469 · Filter by author lumascet opened on May 28, 2020
  7

  

• How can I compile firmware for a V9 board board153v9k?

  synthetos/g2#468 · Filter by author bartona opened on May 28, 2020
  3

  

• 4th Axis Post Processor for Fusion 360

  synthetos/g2#464 · Filter by author chaos-dotcom opened on Apr 23, 2020
  6

• Serial UART Port

  synthetos/g2#461 · Filter by author FranciscoPoloChavez opened on Apr 8, 2020
  1

  

• PCB Auto Level Probing tripping

  synthetos/g2#460 · Filter by author tbs845 opened on Mar 30, 2020
  1

• motor control board for 4 motors (What are you guys using?)

  synthetos/g2#455 · Filter by author DeanCavaliere opened on Feb 17, 2020
  5

• Current state and roadmap for feedrate and spindle overrides

  synthetos/g2#444 · Filter by author karoria opened on Jan 11, 2020